But a shorter-width section with framing on the sides would get a lot of support from the side framing and not necessairly need it on the short edges. The frame is the 'hem' that keeps it together. The raw edges of lattice are prone to popping loose, just like a raw fabric edge might unravel. Edit for clarity: The framing would be to provide some structural support to the lattice. For a section as narrow as a foot or so, you wouldn't necessarily have to frame in the raw ends on the short sides, so you could use the scraps easily (or you could frame them in, if you like the look. That would still frame in the raw ends of the lattice (you may have to trim the long side of sheets a bit to get a good look), but allow you to use the bits cut off from the shorter-post end to fill the gaps rather than needing more full sheets. Rather than the cross-shaped framing you have in the middle of your diagram. So, in ASCII where X is lattice and I is frame (II the posts) it would be sort of. Then in the center, use the cut-offs from the shorter end to make a 1'-wide (or thereabouts) 'stripe'. The first thought that comes to mind is to install the sheets vertically, side-by-side. They helped give me ideas of how to attach everything, but not when the gaps are as big as mine are. Or can they just butt together (I'm thinking no)?Įvery article or video I could find shows examples of really low-to-the-ground decks, which doesn't help much. Also, I will definitely be putting a small frame around each section, but was wondering if I had to have a frame/border where two sheets come together in, say, the middle of a section. I'm willing to frame it like that, if need be, but would appreciate any ideas or possibilities I may be missing. Plus, it seems like a waste of a lot of lattice because the cut-offs will be pretty much useless. The right example looks good and would fill the space, but I would prefer not to spend so much time and money on framing the whole deck out like that. In the middle example, two horizontally positioned sheets would cover the height, but not the more-than-8ft width. With the leftmost position possibility, the 4' x 8' sheet of lattice is tall enough, but the gap is too wide for two side-by-side. The distance between the posts varies a little, but is approximately 9 feet each. Here is a link to the album that will help you understand my problems: r/DIY now has a Discord channel! Come chat with us!ĭid you miss the AMA with Patrick DiJusto? Click here to read it!Īll content must be DIY - if you paid for the work or found it posted online it is not DIY. AMA with Travis Larson is over Check it out!.COVID-19 DIY PPE Post is live, connecting medical professionals with DIYers!.Quinn Dunki of Blondihacks answers your questions! Read her insights into machining and cat dentistry here.This process is free and there is no obligation to continue once you receive your decks price estimate. Get Free Deck Building Price Quotes with No Obligation!įill out our 3-5 minute quick and easy form, and receive a free price quote on decks from one of our pre-screened and licensed deck contractors. Related InformationĪdditional Deck Building and Design Resources The Deck Installation Bid Sheetwill teach your how to hire the right deck contractor, and help to ensure that your deck project is completed on time and budget. I used some additional lumber on the outside corner to dress the corner up a bit.įor help on building a deck, see ’s Deck Installation Bid Sheet. Staining lattice with a brush is a slow and tedious job, however I find by applying the stain by hand that is holds up better.Īfter staining the lattice panels and allowing them to sufficiently dry, I permanently installed the lattice using deck screws. ![]() I stained the lattice using a brush and a transparent decking stain. I then removed them and stained the lattice on the ground. ![]() by a lawnmower in this type of application.Īfter cutting each lattice panel I temporarily fastened them to the side of the deck with one or two exterior grade deck screws to make sure all the panels lined up properly. Plastic lattice is very susceptible to cracking and breakage, and should therefore be limited to applications where it can’t be easily banged, e.g. I highly recommend not using plastic lattice around the bottom of a deck. I am using the thicker 1/4″ lattice so that the deck lattice will standup to the more harsh environment of the lower portion of a deck. In this video I am using 4’x8′ sheets of pressure treated lattice. When replacing old and damaged lattice around a deck, try to save the old lattice pieces as templates for cutting out the new lattice material. In this video Mark Donovan of shows how to install lattice around a deck.
0 Comments
Leave a Reply. |